Updated Nov 17, 2026· 8 min read

Key takeaways

  • Voltage drop can affect results. Inspectors have reported that on branch circuits with a high voltage drop at a 15 amp load, some AFCI breakers did not trip from a plug-in test but did trip with their own TEST button. Whether that applies to a given breaker brand is a question for the breaker maker. A plug-in test that does not trip is a reason to ask an electrician to look, not a reason to defeat anything.
  • Different tools may disagree. Plug-in tools use their own simulated signal. Breaker designs change over time, so follow the manual of the AFCI device and the tester.
  • Shared neutrals. IDEAL’s manual describes a shared-neutral test for AFCI breakers, since a shared neutral can cause nuisance trips. Fixing that is electrician work.
  • Not every outlet. A tester tells you about the circuit behind the outlet you plug into, and the AFCI device may be a breaker at the panel or a combination outlet elsewhere on the circuit.

For a homeowner or inspector who needs to test arc-fault circuit interrupter (AFCI) protection at an outlet, the Klein Tools RT310 AFCI/GFCI outlet tester is the straightforward pass-or-fail choice, the Klein Tools RT390 circuit analyzer adds measured trip values and a voltage-drop load test, and the IDEAL SureTest 61-165 is an older analyzer with an AFCI test that IDEAL’s current manual describes as legacy; the cheaper Klein RT250 is a GFCI tester only and does not test AFCI devices. All of them plug into a standard 120 volt receptacle, which makes them a convenience tool, not a substitute for the breaker’s own test button or a licensed electrician’s judgment. This guide compares what the makers state about each tool and what the tests can and cannot tell you.

What these testers do

An AFCI is a breaker or outlet device that watches for the electrical signature of an arcing fault and opens the circuit. A GFCI watches for current leaking to ground and trips. Standard three-light outlet testers can reveal wiring faults such as reversed polarity or an open ground, but they do not exercise AFCI or GFCI protection. The tools in this guide add that function: they plug into an outlet and simulate a fault, and the protective device should trip. A circuit analyzer goes further and reports measurements.

It is worth being clear about limits. These testers show that a device responds to a simulated condition from the point where you plug in. They do not certify an installation, diagnose hidden wiring defects or replace the maker’s recommended monthly test using the device’s own TEST button. Do not use a plug-in tester to defeat or bypass a device, and do not claim a device prevents fires or injuries. If a device does not trip, or a tester reports a wiring fault, stop and call a licensed electrician; do not open the panel or work on live wiring yourself.

At a glance: current tools and their stated specs

Model Tests Display Key stated specs Limits
Klein Tools RT250 GFCI and wiring faults; not AFCI LCD Shows voltage, wiring fault and GFCI trip time; auto-hold; detects open neutral with open ground; CAT II 135 V No AFCI test
Klein Tools RT310 AFCI and GFCI, plus common wiring faults Indicator lights Simulates arc-fault and ground-fault conditions; detects dual-open fault; 10 in flexible cord; 7.4 x 2.3 x 1.3 in; 8.5 oz; 6.6 ft drop rated; CAT III 135 V; IP40; 3 AAA batteries Pass or fail only; powers off after about 2 minutes
Klein Tools RT390 AFCI, GFCI, wiring faults, voltage drop Color LCD Shows AFCI and GFCI results including trip time and trip current; AC line voltage; 12, 15 and 20 A load tests for percent voltage drop; detachable cord; 10.92 oz with batteries; CAT III 135 V; IP40 Auto power-off per the manual
IDEAL SureTest 61-165 AFCI and GFCI, wiring faults, voltage drop LCD analyzer The manual describes an AFCI test that simulates an arc fault between hot and neutral, a shared-neutral test, and a GFCI test at 6 to 9 mA; voltage drop at 12, 15 and 20 A loads Legacy design per IDEAL’s manual; AFCI test is 61-165 only
IDEAL SureTest 61-164 GFCI, wiring faults and voltage drop LCD analyzer Same family; the manual indicates the AFCI test is limited to the 61-165 No AFCI test

Klein also lists measured ranges for the RT390 in its manual: AC voltage 30.0 to 150.0 V, a 6.0 to 9.0 mA GFCI trip-current window, GFCI trip time of 0 to 6 seconds, an AFCI trip current of 106 to 141 A and AFCI trip time of 0 to 400 ms. One manual revision lists AFCI trip-time accuracy as 2 percent plus or minus 20 ms and another lists 1 percent, so revisions differ. IDEAL lists the SureTest accessories for the 61-164 and 61-165, and the manual describes the voltage-drop and AFCI functions; the manual says references to the 61-165 AFCI function are for legacy users, so confirm the model is still sold before buying.

Choosing between a tester and an analyzer

Pass or fail: the RT310

If all you want to know is whether an AFCI and GFCI device trips and whether the outlet is wired correctly, the RT310 is the simplest. It has lights rather than a screen, a flexible cord that helps with recessed or awkward outlets, and a drop rating that suits a toolbag. The lack of a screen means you read a light code, which takes a minute to learn from the manual.

Numbers: the RT390 and SureTest

A circuit analyzer shows trip time and trip current instead of only a light. This matters when a device trips slowly or not at all, and when you want to see whether the circuit has a high voltage drop under a 12, 15 or 20 amp load. Voltage drop is a measure of how much voltage the wiring loses under load, and a high figure can point to a loose connection or an undersized or overlong run. The RT390 shows this on a color screen. IDEAL’s manual says that if the drop is above 5 percent you should investigate the hot and neutral impedances. These are the kind of numbers an inspector or electrician might use, and the analyzer’s guidance is a pointer, not a diagnosis.

GFCI only: the RT250

If you only care about GFCI outlets in kitchens, baths and garages, the RT250 shows trip time on an LCD and detects an open neutral with an open ground. Retailers list its AFCI field as no, so do not buy it for AFCI work.

Known quirks of AFCI testing

  • Voltage drop can affect results. Inspectors have reported that on branch circuits with a high voltage drop at a 15 amp load, some AFCI breakers did not trip from a plug-in test but did trip with their own TEST button. Whether that applies to a given breaker brand is a question for the breaker maker. A plug-in test that does not trip is a reason to ask an electrician to look, not a reason to defeat anything.
  • Different tools may disagree. Plug-in tools use their own simulated signal. Breaker designs change over time, so follow the manual of the AFCI device and the tester.
  • Shared neutrals. IDEAL’s manual describes a shared-neutral test for AFCI breakers, since a shared neutral can cause nuisance trips. Fixing that is electrician work.
  • Not every outlet. A tester tells you about the circuit behind the outlet you plug into, and the AFCI device may be a breaker at the panel or a combination outlet elsewhere on the circuit.

Budget, mid-range and premium tiers

Tier Typical choice Fit
Budget Klein RT250 (GFCI only) A homeowner who only tests GFCI outlets
Mid-range Klein RT310 AFCI and GFCI pass or fail for a home or small contractor
Premium Klein RT390, IDEAL SureTest 61-165 Inspectors and electricians who need trip values and voltage-drop data

Pick one if

Pick this If
RT250 You only need GFCI tests and wiring-fault checks
RT310 You want a compact AFCI and GFCI tester with indicator lights
RT390 You want trip time, trip current and voltage drop on a color screen
SureTest 61-165 You already own or find this legacy analyzer and want its shared-neutral test

Safety and use notes

  • Read the manual first. The tools are rated for 120 volt North American outlets with three wires. They do not work on other systems. Klein lists CAT III 135 V ratings for the RT310 and RT390; do not use them where the voltage may exceed that.
  • Do not use a tester to bypass a device. Never reset or disable a protective device to force a test to pass.
  • Licensed electrician for repairs. A wiring-fault light, a device that does not trip, or a high voltage drop calls for a licensed electrician. Do not open the panel or alter wiring yourself.
  • Use the device’s own test button too. Makers recommend regular testing with the TEST button on the AFCI or GFCI device, and the plug-in tool is an extra check.
  • Batteries and storage. The Klein models use three AAA batteries and power off after a few minutes. Replace batteries when readings flicker.
  • Test circuits with loads connected cautiously. Unplug sensitive electronics from the circuit before testing, as the manuals advise.

Alternatives

  • Basic receptacle testers. Cheap three-light testers show polarity and ground faults but do not exercise AFCI or GFCI devices.
  • Combination GFCI testers with voltage detection. IDEAL lists GFCI receptacle and voltage testers for simple tasks.
  • Hiring an electrician or inspector. For a home purchase or a suspected circuit problem, a professional with the right tools and judgment is a better route than a plug-in test alone.

Frequently Asked Questions

Does the Klein RT250 test AFCI?

No. Retailer spec sheets list AFCI as not supported, and Klein positions the RT310 and RT390 for AFCI testing. Buy one of those if you need AFCI results.

What is the difference between the RT310 and RT390?

The RT310 gives a pass or fail with indicator lights. The RT390 shows measured values on a color LCD, including trip time and trip current, line voltage and a voltage-drop load test at 12, 15 and 20 amps.

Why would a plug-in test fail when the breaker’s own button works?

Inspectors have reported that high voltage drop on a circuit can affect plug-in AFCI tests on some breakers. Do not defeat anything. Ask a licensed electrician to evaluate the circuit and consult the breaker maker’s guidance.

Can I test every circuit in my house with one?

You can test circuits through the outlets you plug into. Lighting circuits and hardwired loads are not reachable this way. An electrician can cover those.

Is a plug-in tester a substitute for the breaker test button?

No. Makers instruct users to test with the device’s own button regularly. The plug-in tool is an additional check of the circuit.

Are these safe for a homeowner to use?

They are designed to plug into a standard outlet, and the manuals describe the use. Follow the instructions, do not open panels, and call a licensed electrician for any fault or repair.

A
admin
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.