Updated Nov 17, 2026· 7 min read

Key takeaways

  • Hire a licensed electrician. The device connects to the service panel and needs a breaker position, short conductors and correct grounding. This is not a home project. Follow the maker’s instruction sheet and local code, including any permit requirements.
  • Breaker size. Makers differ: Eaton’s install sheet for the base model recommends a dedicated 2-pole 15 A breaker, the ULTRA recommends a 50 A 2-pole breaker, and Siemens recommends a 20 A breaker. Use what the instruction sheet for your model says.
  • Lead length. The Siemens installation notes ask for leads as short and straight as possible, with the device mounted close to the panel. Long leads raise the let-through voltage and reduce the benefit.
  • Panel brand. Eaton says its device can mount outside any manufacturer’s load center, and Siemens says its device installs onto any brand of load center, but the instruction sheets list limits. Read them and let the electrician confirm.
  • Do not bypass anything. Never remove a safety device or defeat a breaker to make room. The electrician should use a proper breaker position or approved method.
  • Indoor and outdoor. Eaton’s install sheet says its unit is intended for both indoor and outdoor use, and Siemens lists a NEMA 4X rating. Confirm the mounting location suits the enclosure rating.

For a typical North American house, single-phase surge protection means a whole-home surge protective device (SPD) on the 120/240 volt split-phase service, and the current choices that fit a normal panel are the Eaton Complete Home Surge Protection family (CHSPT2SURGE, CHSPT2SURGE10 and CHSPT2ULTRA) and the Siemens FirstSurge Plus (FS100); pick by surge-current rating and by whether the maker supports your panel brand. These devices connect to the electrical panel, so installation belongs to a licensed electrician following the maker’s instructions and local code. This guide explains what single phase means, how to compare ratings, and what to ask the installer.

What “single phase” means for a home

Most houses in North America are supplied with single-phase power: two 120 volt legs that together give 240 volts for large appliances, plus a neutral. Utilities call it split phase. Commercial and industrial buildings often use three-phase service, which needs different devices. The SPDs here are rated for 120/240 volt single-phase, sixty hertz service. Do not use a single-phase device on a three-phase panel, and do not install a device whose voltage rating does not match your service. If you are unsure what you have, the electrician or the utility can tell you.

A whole-home SPD does not replace plug-in surge strips. It reduces the size of spikes entering at the panel, so the strips at your desk and TV have less to deal with. Makers do not claim it stops every event, and nothing in this guide says it prevents fire or damage. Think of it as a first layer in a layered approach.

At a glance: current models and stated specs

Model Type and service Stated ratings Install notes
Eaton CHSPT2SURGE Type 2 CHSP, 120/240 V single phase, 60 Hz, NEMA 4 enclosure 5 kA nominal discharge, 36 kA surge current, 22 kA SCCR; VPR 700 V L-N, 1200 V L-L, 900 V N-G, 700 V L-G; MCOV 150 V L-N and 300 V L-L Install sheet recommends a dedicated 2-pole 15 A breaker; can mount outside any maker’s load center
Eaton CHSPT2SURGE10 Same family 10 kA nominal discharge, 60 kA surge current Listed in the same product family
Eaton CHSPT2ULTRA Same family 600 V L-N VPR, 20 kA nominal discharge, 108 kA surge current Install sheet recommends a 50 A 2-pole breaker
Siemens FirstSurge Plus (FS100) UL 1449 Type 2, 120/240 split phase, panels up to 400 A 100,000 A rating; VPR 600 V for L-N, L-G and N-G and 900 V L-L; MCOV 150 V and 300 V; SCCR 100 kA NEMA 4X, indoor or outdoor; recommended breaker 20 A; mounts on any brand of load center; 10 year warranty

Eaton lists the first model with UL 1449 recognition and cUL certification and a limited lifetime warranty. Siemens’ FirstSurge line has been moving toward its newer BoltShield series, and some distributors show the FirstSurge Plus as unavailable to order, so confirm that the FS100 is still sold before planning around it. The larger FS140 is treated as phased out and is not recommended here, and older Square D units are likewise left out; if an electrician proposes one, ask whether it is still manufactured and supported.

How to compare the numbers

Surge current rating

Expressed in kiloamps, it describes how much surge current the device is built to handle. Eaton’s CHSPT2SURGE lists 36 kA, the SURGE10 lists 60 kA and the ULTRA lists 108 kA; Siemens’ FS100 lists 100 kA. Higher ratings suggest a larger margin and a longer life under repeated events. Homes in lightning-prone regions or at the end of a long overhead line may justify the higher end. A modest rating is still a meaningful upgrade over no protection.

Voltage protection rating (VPR)

VPR is the let-through voltage measured under a standard test; lower is better. Eaton’s ULTRA lists 600 V line to neutral and the base model lists 700 V. Siemens lists 600 V on three modes. A few hundred volts difference may matter for sensitive electronics, but compare like for like, since the modes and test standard are the same under UL 1449.

Maximum continuous operating voltage (MCOV)

A 120/240 service needs an MCOV above the highest normal voltage. Both makers list 150 V line to neutral and 300 V line to line, which is typical for this service.

Short circuit current rating (SCCR)

This number must be at least as high as the available fault current at your panel. Eaton lists 22 kA for the base model, and Siemens lists 100 kA for the FS100. The electrician or inspector can confirm what applies to your service.

Status indication

A device that fails silently gives false confidence. Siemens lists ground reference monitoring and three-stage notification on the FirstSurge Plus. Choose a device with a clear status light or alarm and check it periodically as the manual says.

Installation and compatibility notes

  • Hire a licensed electrician. The device connects to the service panel and needs a breaker position, short conductors and correct grounding. This is not a home project. Follow the maker’s instruction sheet and local code, including any permit requirements.
  • Breaker size. Makers differ: Eaton’s install sheet for the base model recommends a dedicated 2-pole 15 A breaker, the ULTRA recommends a 50 A 2-pole breaker, and Siemens recommends a 20 A breaker. Use what the instruction sheet for your model says.
  • Lead length. The Siemens installation notes ask for leads as short and straight as possible, with the device mounted close to the panel. Long leads raise the let-through voltage and reduce the benefit.
  • Panel brand. Eaton says its device can mount outside any manufacturer’s load center, and Siemens says its device installs onto any brand of load center, but the instruction sheets list limits. Read them and let the electrician confirm.
  • Do not bypass anything. Never remove a safety device or defeat a breaker to make room. The electrician should use a proper breaker position or approved method.
  • Indoor and outdoor. Eaton’s install sheet says its unit is intended for both indoor and outdoor use, and Siemens lists a NEMA 4X rating. Confirm the mounting location suits the enclosure rating.

Budget, mid-range and premium tiers

Tier Typical choice What you get
Budget Eaton CHSPT2SURGE Type 2 protection with a modest surge-current rating and a compact housing
Mid-range Eaton CHSPT2SURGE10, Siemens FS100 Higher surge-current ratings, status monitoring on the Siemens unit
Premium Eaton CHSPT2ULTRA The highest surge-current rating in the Eaton family and a lower VPR

Pick one if

Pick this If
CHSPT2SURGE You want a compact, entry-level whole-home device from a major panel maker
CHSPT2SURGE10 You want a higher rating without moving to the top model
CHSPT2ULTRA You want the highest rating in the Eaton family and have a 50 A breaker position available
FS100 You want a 100 kA device with monitoring, and your panel is under 400 A

Questions to ask the electrician

  • Is there a free breaker position near the neutral and ground bars so the leads stay short?
  • What breaker size does the instruction sheet for the chosen model call for, and does the panel have room for a 2-pole device?
  • Does the permit process in your area require an inspection after the device is installed?
  • Where is the status light or alarm, and how will I know if it changes?
  • Are other buildings on the property, such as a detached garage with its own panel, worth protecting as well?

Bringing the model number and the maker’s installation sheet to the first visit usually shortens the job and avoids a second trip.

Alternatives and companions

  • Plug-in surge strips. Still useful at the desk and television for the spikes generated inside the house. See the other guides in this series for desk and backup options.
  • Utility meter-socket devices. Some utilities or electricians offer meter-base surge devices. Ask the utility or your electrician what is permitted in your area.
  • Data-line protectors. Surges also arrive on coax and Ethernet. Whole-home devices do not cover those lines.

Frequently Asked Questions

What is the difference between Type 1 and Type 2?

Under UL 1449, Type 1 devices may be installed ahead of the main service disconnect, and Type 2 devices are installed on the load side. The Eaton CHSP models and the Siemens FirstSurge Plus are listed as Type 2. Ask the electrician which is allowed in your jurisdiction.

Can I install a whole-home surge protector myself?

The device connects inside the electrical panel, where live conductors are exposed. A licensed electrician should install it, following the manual and local code.

Will it protect against a direct lightning strike?

No maker promises that. These devices reduce the surge that enters through the service; a direct strike can exceed any rating. Treat the device as one layer of protection.

How do I know if it has failed?

Look at the status light or alarm described in the manual. Siemens lists status indication on its unit; Eaton’s instruction sheet explains its indicators. If the light shows a fault, call an electrician.

Do I still need plug-in strips?

Yes. A panel device does not stop spikes generated inside the home, such as motors cycling, and cannot protect phone, coax or Ethernet lines.

Does it need a dedicated breaker?

The makers’ instruction sheets say what overcurrent device to use. Eaton recommends a dedicated 2-pole breaker for the base model to achieve its published rating. Follow the sheet for your model.

A
admin
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.