Key takeaways
- Outdoor device. Put one protector near the device and one at the building entry or switch end. Tripp Lite states that two units are required for the outdoor models to protect both ends. Ubiquiti’s datasheet also suggests two units, one near the CPE and one at the building entry.
- Between buildings. A shed, garage or detached office with its own power and ground is the classic case. Cable runs between structures can carry a spike when the grounds differ. Ask a qualified installer about bonding the grounds, since that is mains-related work.
- Indoor closet. A five-port in-line unit can protect a few PoE cameras at the switch. It does not protect the cameras’ far end.
- Weather. The Ubiquiti unit lists IPX5 weatherproofing, the Tripp Lite B110-SP-CAT-OD2 lists IP68, so pick according to exposure. Even a weatherproof protector should be mounted so water cannot sit in the ports.
“Low voltage surge protection” is most clearly about protecting the thin data and power-over-Ethernet cables in a home or small office, not the 120 volt outlets, and the best match for most people is an in-line Ethernet surge protector: the Ubiquiti ETH-SP-G2 or the Eaton Tripp Lite B110-SP-POE-1 for a single camera or access point, the Tripp Lite B110-SP-CAT-OD2 for an outdoor run, the B110-SPPOEC-A5 for a rack of five ports, and the B110-SP-10G for a fast non-PoE link. These parts sit in the cable between the building entry or switch and the device and shunt a spike to ground. This guide explains how to choose by speed, PoE standard and location, and what each maker states.
Why low-voltage lines need their own protection
A surge does not have to come through the power cord. A long Ethernet cable to an outdoor camera or a rooftop access point acts like an antenna, and a nearby lightning event or a ground-potential difference between two buildings can push a spike down the wire into the switch or router. A plug-in power strip cannot stop that, because the strip only sees the AC path. Low-voltage protectors are small devices with two RJ45 ports that sit in line with the cable and a ground connection. They protect the data pairs and, for PoE models, the power pairs too.
Ground is the essential part. A protector without a good path to ground cannot divert much. Follow the maker’s instructions for grounding, use a proper grounding point, and for outdoor or building-entry installations that involve grounding conductors, a licensed electrician or qualified installer should handle the work according to local code. These products are not a guarantee against damage, and no maker states they prevent fires or injuries.
At a glance: current in-line protectors
| Model | Best for | Key stated specs | Limits |
|---|---|---|---|
| Ubiquiti ETH-SP-G2 | Outdoor cameras, access points and PoE radios | Two surge-protected RJ45 ports; discharge rating reported as 5 kA or 10 kA depending on source; operating range -30 to 65 C; the maker lists 10/100/1000 Mbps and 802.3af PoE | One retailer lists 2.5 Gbps, which the maker documents do not confirm; some sellers show it as discontinued |
| Eaton Tripp Lite B110-SP-POE-1 | Single in-line PoE device | Meets 802.3af and 802.3at; speeds up to 1 Gbps; plug-and-play with no software or external power | Single port |
| Eaton Tripp Lite B110-SP-CAT-OD2 | Outdoor PoE runs | IP68; maker lists 802.3af, at and bt with up to 90 W DC power; up to 1 Gbps; ESD protection of 15 kV air and 8 kV contact | Needs two units to protect both source and device |
| Eaton Tripp Lite B110-SPPOEC-A5 | Five-port rack or closet use | 1U rack mount; 802.3af, 802.3at and 802.3bt Type 4; up to 1 Gbps | Rack-mount form factor |
| Eaton Tripp Lite B110-SP-10G | Non-PoE links at up to 10 Gbps | In-line network surge protector for Cat6a | No PoE |
The Ubiquiti figures include a DC spark-over voltage of 90 V at 100 V per second and a maximum impulse spark-over of 700 V at 1 kV per microsecond, with 1.0 pF capacitance. Retailer pages describe speed and PoE support differently from the maker’s datasheet, so confirm the standard your camera or access point uses.
Choosing by speed and PoE standard
Data speed
Protectors add a tiny amount of capacitance, and some are limited by the cable category. Gigabit links work with all the listed models. Ubiquiti’s own documents list 10/100/1000 Ethernet for the ETH-SP-G2, and one retailer’s claim of 2.5 Gbps support is not confirmed there, so treat it as a gigabit part. If your network runs faster, look at another model; for 10 Gbps, Tripp Lite lists the B110-SP-10G, built for Cat6a. Using a gigabit-only protector on a faster link will bring the link down to its limit or break it.
Power over Ethernet
PoE has several standards: 802.3af (lower power), 802.3at (higher), and 802.3bt (highest, Types 3 and 4). A protector must pass the power pairs without choking them. Tripp Lite lists B110-SP-POE-1 for af and at, and the B110-SPPOEC-A5 for af, at and bt Type 4. The outdoor B110-SP-CAT-OD2 lists support up to 90 W of DC power. If your device draws more than the standard the protector lists, pick a different model. Ubiquiti’s documents cite 802.3af and do not mention 802.3at, so read the device label and the camera’s manual before using it with a higher-power camera.
Planning a small install
Before buying, list every low-voltage device that leaves the building envelope: outdoor cameras, a doorbell, a garage access point, a detached office. Note the PoE standard and cable category for each, count how many protectors you need (usually two per outdoor run), and sketch where the ground connection will come from. This short plan prevents buying the wrong speed or standard and makes the conversation with an installer quicker.
Cable category
The B110-SP-10G is aimed at Cat6a cable. The 1 Gbps models list Cat5e and Cat6 on their pages. Use the cable type the maker states.
Where to put them
- Outdoor device. Put one protector near the device and one at the building entry or switch end. Tripp Lite states that two units are required for the outdoor models to protect both ends. Ubiquiti’s datasheet also suggests two units, one near the CPE and one at the building entry.
- Between buildings. A shed, garage or detached office with its own power and ground is the classic case. Cable runs between structures can carry a spike when the grounds differ. Ask a qualified installer about bonding the grounds, since that is mains-related work.
- Indoor closet. A five-port in-line unit can protect a few PoE cameras at the switch. It does not protect the cameras’ far end.
- Weather. The Ubiquiti unit lists IPX5 weatherproofing, the Tripp Lite B110-SP-CAT-OD2 lists IP68, so pick according to exposure. Even a weatherproof protector should be mounted so water cannot sit in the ports.
Budget, mid-range and premium tiers
| Tier | Typical choice | Fit |
|---|---|---|
| Budget | Ubiquiti ETH-SP-G2, Tripp Lite B110-SP-POE-1 | One or two cameras or access points on gigabit PoE |
| Mid-range | Tripp Lite B110-SP-CAT-OD2 | Outdoor runs with high-power PoE needs |
| Premium | Tripp Lite B110-SPPOEC-A5, B110-SP-10G | Rack ports with bt support, or 10 Gbps links |
Pick one if
| Pick this | If |
|---|---|
| ETH-SP-G2 | You run Ubiquiti or similar gear and want a compact outdoor-rated protector |
| B110-SP-POE-1 | You have one PoE device on a gigabit link and want plug-and-play |
| B110-SP-CAT-OD2 | You need an IP68 unit and up to 90 W of PoE power |
| B110-SPPOEC-A5 | You have several PoE devices at a closet or rack and may use 802.3bt |
| B110-SP-10G | You run a 10 Gbps link on Cat6a without PoE |
Other low-voltage lines
Ethernet is one path. Coaxial lines for cable internet and satellite, telephone lines, alarm panels and landscape lighting transformers all carry low voltage and can carry surges. Some power strips and UPS units include coax and phone protection ports, such as the Tripp Lite TLP1208SAT, which lists 12 outlets, 2880 joules and telephone, modem, coaxial and Ethernet protection. For security cameras or alarm systems with DC power adapters, a protector rated for the voltage on that line is the right tool, and the maker’s data sheet should state its working voltage. Do not guess.
Safety and grounding notes
- Follow the maker’s grounding instructions. The ground connection is what makes the device work.
- Licensed help for mains work. If grounding or bonding involves the electrical panel or a ground rod, a licensed electrician should do it to local code.
- Do not defeat other protections. Do not remove an existing protective device to add one of these.
- Replace after a heavy event. Protectors can be spent by a large surge. Follow the maker’s guidance on replacement.
- Do not claim safety outcomes. A protector reduces exposure; it does not guarantee equipment survives.
Alternatives
- Fiber links. Glass fiber carries no electrical surge, which is why it is used between buildings. An optical converter at each end isolates the equipment, although both ends still need power.
- PoE switches with surge protection. Some network gear includes protection on its ports, as the maker states.
- Whole-home AC protection. A panel device addresses the power side while low-voltage protectors address the data side. They complement each other.
Frequently Asked Questions
Do I need a protector at both ends of the cable?
For outdoor runs, yes. Tripp Lite states two units are required for its outdoor models to protect both the source and the device. Ubiquiti’s datasheet suggests one near the device and one at the building entry.
Will a surge protector slow my internet?
A protector rated for your link speed should not. Gigabit models work for gigabit links, and the 10G model is built for faster links. A mismatched protector could limit speed.
Does my PoE camera work through it?
Only if the protector supports the camera’s PoE standard and power draw. The B110-SP-POE-1 lists 802.3af and at, the B110-SPPOEC-A5 lists up to 802.3bt Type 4, and the CAT-OD2 lists up to 90 W.
Is grounding really necessary?
Yes. The device diverts the spike to ground, so it needs a proper ground path. Follow the maker’s instructions and hire a qualified installer if the work touches the electrical system.
Can this stop lightning damage?
No maker promises that. A direct strike can exceed any rating. These devices reduce the exposure from nearby events.
Does it cover coax and phone lines?
Not the Ethernet models. Some power strips and UPS units include coax, phone and Ethernet protection ports, and separate coax protectors exist for incoming cable lines.
Read next